The structural systems of the washing equipment are the control system, the barrel, the drum, the transmission mechanism, the shock absorber, the door, etc.; in addition, in terms of maintenance, the clothes should be checked for other sundries during washing, and the washing capacity should not exceed the standard. The sewage must be thoroughly discharged, etc. The relevant content will be introduced in detail below.
1. Structural system of washing equipment
1. Control system
It is composed of computer panel, computer chip, program software, various sensors, etc.
2. Barrel body
It is welded by stainless steel plate, used to hold washing water, and connect with water inlet pipe and drain valve. The internal surface is specially treated to prevent corrosion. The front of the barrel is equipped with a door, a soap tank is installed on the top, a heater and a drain valve are installed in the lower sink, and the barrel is fixed on the base of the machine through a shock absorber.
3. Roller
The drums are all made of high-quality stainless steel plates, and the drums are used to hold laundry. The wall of the tube is equipped with small overflow holes and tipping ribs, so that the clothes are constantly tumbled in the tube. The front end of the drum is a clothing door, and the rear end is installed on the barrel through a shaft seat.
4. Transmission mechanism
The transmission mechanism is composed of a frequency converter, a frequency conversion motor, a belt pulley, a triangular belt and a bearing seat. The machine can obtain three required speeds of washing, uniform distribution and dehydration.
5. Shock-absorbing mechanism
The shock absorber is fixed on the base of the machine by compression springs, pull rods, hooks and supports. The barrel, cylinder, transmission mechanism and other main components are all suspended on the support of the shock absorber through pull rods. The machine produces during high-speed dehydration. The vibration is weakened by the spring, and there are dampers on the left and right sides of the machine to reduce the swing amplitude during vibration.
6. Door
It is used for loading and unloading clothes. The door body is made of stainless steel. The door is equipped with a rubber sealing ring, which is sealed with the barrel body when working. The door lock is used to open or close the door. A linkage switch is installed in the door lock to ensure that the door is in operation. Will not be opened to ensure the safety of the operator.
7. Water inlet pipeline
A solenoid valve is installed on the water inlet pipe.
8. Drain valve
The opening and closing of the drain valve is controlled by a solenoid valve.
9. Heater
This machine has two heating methods, one is steam heating, and the other is electric heating. The steam heating is controlled by a pneumatic valve, and the electric heating is equipped with 3 sets of electric heating tubes.
2. Main points of maintenance of washing equipment
1. Check the clothes before washing: Check whether there are coins and other sundries in the clothes pockets before washing, to avoid metal objects wearing the washing machine inner tube or jamming the impeller during washing, causing the motor to overload and burn out.
2. The washing capacity does not exceed the standard: If the large-scale washing machine puts too much clothes in the washing, not only the washing degree is low, but also it may cause overload and burn the motor.
3. After washing, drain the sewage thoroughly: after each washing, drain the sewage, clean the large washing machine bucket with clean water, and then use a dry cloth to wipe the water droplets and stagnant water inside and outside the washing machine, and then place it in a dry and ventilated place.
4. Pay attention to cleaning work: Do not use strong alkalis, gasoline, vinyl materials and hard brushes when cleaning the washing machine, and do not use hard utensils when cleaning the filter screen and drain pipe.
5. Keep in mind for safety protection: The metal shell and electrical parts of the large washing machine are insulated. When the washing machine is not used for a long time, do not place it in a humid environment to avoid the aging of the insulation and cause the housing to become charged. In addition, when using the washing machine, you must pay attention to ensure that the socket grounding wire has a safe and good performance. 1. Check the clothes before washing. Before washing, check whether there are coins and other sundries in the clothing pockets, to avoid metal objects abrading the inner tube of the large washing machine or jamming the pulsator during washing, causing the motor to overload and burn out.
6. As the mold is very sensitive to temperature, the survival rate in 35°C water is very low, and it is almost zero in 45°C hot water, so cleaning with 45°C hot water can also effectively kill the mold.
The above is all about "what are the structure of washing equipment and what are the main points of maintenance", I hope it will be helpful to you
